Cryogenics

Introduction

The term “Cryogenics” originates from Greek word which means creation or production by means of cold. As prices for energy and raw materials rise and concern for the environment makes safe waste disposal difficult and Costly, resource recovery becomes a vital matter for today’s business. Cryogenic grinding technology can efficiently grind most tough materials and can also   facilitate Cryogenic recycling of tough composite materials and multi component scrap. The heart of this technology is the CRYO-GRIND SYSTEM. It employs a cryogenic process to embrittle and grind materials to achieve consistent particle size for a wide range of products. The cryogenic process also has a unique capability for recycling difficult to separate composite materials.

Cryogenic grinding is a method of powdering herbs at sub-zero temperatures ranging from 0 to minus 70°F. The herbs are frozen with liquid nitrogen as they are being ground. This process does not damage or alter the chemical composition of the plant in any way. Normal grinding processes which do not use a cooling system can reach up to 200°F. These high temperatures can reduce volatile components and heat-sensitive constituents in herbs. The cryogenic grinding process starts with air-dried herbs, rather than freeze-dried herbs.

Solid materials are ground or pulverized by way of hammer mills, attrition mills, granulators or other equipment. A smaller particle size is usually needed to enhance the further processing of the solid, as in mixing with other materials. A finer particle also helps in melting of rubber and plastics for molding. However, many materials are either very soft or very tough at room temperatures. By cooling to cryogenic temperatures with liquid nitrogen, these may be embrittled and easily fractured into small particles.

A scientifically controlled study using four herbs was conducted at Frontier Herbs in the Fall of 1996, comparing cryogenic grinding methods with normal grinding methods. The herbs tested included feverfew, goldenseal, valerian and echinacea. In all cases the cryogenically ground herb contained greater amounts of the constituents tested. Feverfew herb showed the greatest difference, with the cryogenically ground herb containing 21.8% higher levels of parthenolide, the primary active constituent. Valerian root showed an 18.7% increase in valerenic acid when cryogenically ground. Goldenseal root showed a 16.4% increase in berberine and 10.7% increase in hydrastine. Lastly, Echinacea purpurea root showed a 12.1% increase in total phenolic content in the cryogenically ground root. Test results were obtained by HPLC (high performance liquid chromatography) methods.

Cryogenic grinding was shown to significantly affect active constituent levels in herbs. Test results showed an average increase of 15.6% in constituents tested in four medicinal herbs when they were ground cryogenically. The range was 10.7% to 21.8%, indicating that some herbs are affected more than others by the temperatures at which they're ground.

APPLICATION OF CRYOGENICS

The major areas in which cryogenics find its applications are : -

1. Gas Industry – in air separation. The volume of production of nitrogen and Oxygen by cryogenic separation of air is the important of the separation of air, refrigeration and separation. In the separation column, the difference in the boiling points of the constituents of air is used to separate them out.

2. As the source of gas. For example, the breathing oxygen needed for the pilots of the fighter aircraft is supplied by vaporizing liquid oxygen on board. In this way is a weight reduction of 65% and space reduction of 85%.

3. In space research – as rocket propellant and for space simulation. The most important advantage of cryogenic fuels is that these have very high specific impulse when compared to other fuels (specific impulse is kgs of thrust produced per kg of propellant per sec). The value is approximately 500 for cryogenic fuels whereas it is about 250 for alcohol oxygen mixture.

4. In biology – for preservation and in treatment of diseases.

5. In food industry – for food handling and processing

6. In electronics – both semiconductor and superconductor electronics for better signal to noise ratio speed etc

7. In miscellaneous applications such as cryogenic grinding , freezing pipelines for repairs, shrink fitting, fire fighting, etc

8. In medicine – Magnetic Resonance Imaging, Magnetic Resonance Spectroscopy (MRS), Magneto Cardio Graphy (MCG), etc.

9. In nuclear and high – energy physics

10. Metal fabrication

 Download the ppt and the doc file;-https://drive.google.com/drive/folders/1kBuhxQPwaRiSEvysDloVoikY4ERNSfNU?usp=sharing